Basic processing method of public address power amplifier machine <br> No electricity: Check whether the power line to the fuse is open, whether the power line is broken or the fuse is in poor contact, the fuse is blown → check the rectifier bridge or electrolysis of the power amplifier rectifier power supply Whether the device is bad, such as rectifier diode or bridge stack, replace the good components and check other lines, such as power amplifier tubes.
The signal level indicator flashes normally, but there is no sound output: first check if the speaker unit is normal. If it is normal, check the speaker lead is normal, that is, check that the terminal is in good contact, normal, that is, open the case for visual inspection or listen to the ear or hear it. See if the output relay is closed. If the suction is normal, (if there is a universal meter), it is measured whether the front input and output of the relay are directly connected. If it is not connected, the contact in the relay is oxidized or fired to produce charcoal. The relay is normal.
The power light indicates normal no sound output, but the output relay hears the sound: first use the universal meter to measure whether the power supply of the power amplifier is normal, such as normal, that is, the signal line terminal of the signal input terminal is connected with the hand. The large current sound is the initial judgment that the power amplification part is basically normal, that is, whether the signal line of the light shaking signal is incapable or poorly contacted. If the contact is poor, the measurement with the universal meter is that the line is faulty and normal.
For example, when the power amplifier is output, there is no sound output: that is, it is normal to check the speaker unit. If the terminal is in poor contact, it will cause burnt. If the terminal is black, clean it to ensure normal contact, and tighten the screw.
The power-on protection light is on: First, use the universal meter to measure whether the speaker group has a short circuit, and whether the resistance is reduced (generally normal is not less than 30Ω). If the resistance value of the external circuit is normal, it is determined that the power amplifier is faulty, that is, it must be turned on.
The possibility that public broadcast sounds may occur when there are large and small phenomena is :
1. Poor contact of the signal line;
2. Poor contact of the potentiometer;
3. Signal coupling capacitor;
4. The feedback resistor is in poor contact.
In the case of measuring the power amplifier motherboard is normal, there is no sound:
The signal line is not connected or the coupling capacitor is open;
2. The front side has no power supply and measures the power supply part;
3, the volume potentiometer is bad;
4. This fault occurs when the operational amplifier IC is bad.
If the pure power amplifier sound is distorted, the faulty part:
1. Power tube soft breakdown;
2. There is no voltage or low voltage between positive and negative voltages;
3. Resistance variable value, etc.
The sound normal level indicator does not work:
1. First measure whether the voltage is normal;
2. Then measure whether the signal is sent;
3. Measure whether the components are damaged.
The treble bass can't be adjusted:
1. Is the potentiometer normal?
2. Whether the voltage is normal;
3. Whether the RC component is normal;
4. Whether the line is connected or has poor contact;
5. Whether there are any solder joints or false solder joints in the solder joints.
Basic processing method of public address power amplifier machine <br> No electricity: Check whether the power line to the fuse is open, whether the power line is broken or the fuse is in poor contact, the fuse is blown → check the rectifier bridge or electrolysis of the power amplifier rectifier power supply Whether the device is bad, such as rectifier diode or bridge stack, replace the good components and check other lines, such as power amplifier tubes.
The signal level indicator flashes normally, but there is no sound output: first check if the speaker unit is normal. If it is normal, check the speaker lead is normal, that is, check that the terminal is in good contact, normal, that is, open the case for visual inspection or listen to the ear or hear it. See if the output relay is closed. If the suction is normal, (if there is a universal meter), it is measured whether the front input and output of the relay are directly connected. If it is not connected, the contact in the relay is oxidized or fired to produce charcoal. The relay is normal.
The power light indicates normal no sound output, but the output relay hears the sound: first use the universal meter to measure whether the power supply of the power amplifier is normal, such as normal, that is, the signal line terminal of the signal input terminal is connected with the hand. The large current sound is the initial judgment that the power amplification part is basically normal, that is, whether the signal line of the light shaking signal is incapable or poorly contacted. If the contact is poor, the measurement with the universal meter is that the line is faulty and normal.
For example, when the power amplifier is output, there is no sound output: that is, it is normal to check the speaker unit. If the terminal is in poor contact, it will cause burnt. If the terminal is black, clean it to ensure normal contact, and tighten the screw.
The power-on protection light is on: First, use the universal meter to measure whether the speaker group has a short circuit, and whether the resistance is reduced (generally normal is not less than 30Ω). If the resistance value of the external circuit is normal, it is determined that the power amplifier is faulty, that is, it must be turned on.
The possibility that public broadcast sounds may occur when there are large and small phenomena is :
1. Poor contact of the signal line;
2. Poor contact of the potentiometer;
3. Signal coupling capacitor;
4. The feedback resistor is in poor contact.
In the case of measuring the power amplifier motherboard is normal, there is no sound:
The signal line is not connected or the coupling capacitor is open;
2. The front side has no power supply and measures the power supply part;
3, the volume potentiometer is bad;
4. This fault occurs when the operational amplifier IC is bad.
If the pure power amplifier sound is distorted, the faulty part:
1. Power tube soft breakdown;
2. There is no voltage or low voltage between positive and negative voltages;
3. Resistance variable value, etc.
The sound normal level indicator does not work:
1. First measure whether the voltage is normal;
2. Then measure whether the signal is sent;
3. Measure whether the components are damaged.
The treble bass can't be adjusted:
1. Is the potentiometer normal?
2. Whether the voltage is normal;
3. Whether the RC component is normal;
4. Whether the line is connected or has poor contact;
5. Whether there are any solder joints or false solder joints in the solder joints.
Basic processing method of public address power amplifier machine <br> No electricity: Check whether the power line to the fuse is open, whether the power line is broken or the fuse is in poor contact, the fuse is blown → check the rectifier bridge or electrolysis of the power amplifier rectifier power supply Whether the device is bad, such as rectifier diode or bridge stack, replace the good components and check other lines, such as power amplifier tubes.
The signal level indicator flashes normally, but there is no sound output: first check if the speaker unit is normal. If it is normal, check the speaker lead is normal, that is, check that the terminal is in good contact, normal, that is, open the case for visual inspection or listen to the ear or hear it. See if the output relay is closed. If the suction is normal, (if there is a universal meter), it is measured whether the front input and output of the relay are directly connected. If it is not connected, the contact in the relay is oxidized or fired to produce charcoal. The relay is normal.
The power light indicates normal no sound output, but the output relay hears the sound: first use the universal meter to measure whether the power supply of the power amplifier is normal, such as normal, that is, the signal line terminal of the signal input terminal is connected with the hand. The large current sound is the initial judgment that the power amplification part is basically normal, that is, whether the signal line of the light shaking signal is incapable or poorly contacted. If the contact is poor, the measurement with the universal meter is that the line is faulty and normal.
For example, when the power amplifier is output, there is no sound output: that is, it is normal to check the speaker unit. If the terminal is in poor contact, it will cause burnt. If the terminal is black, clean it to ensure normal contact, and tighten the screw.
The power-on protection light is on: First, use the universal meter to measure whether the speaker group has a short circuit, and whether the resistance is reduced (generally normal is not less than 30Ω). If the resistance value of the external circuit is normal, it is determined that the power amplifier is faulty, that is, it must be turned on.
The possibility that public broadcast sounds may occur when there are large and small phenomena is :
1. Poor contact of the signal line;
2. Poor contact of the potentiometer;
3. Signal coupling capacitor;
4. The feedback resistor is in poor contact.
In the case of measuring the power amplifier motherboard is normal, there is no sound:
The signal line is not connected or the coupling capacitor is open;
2. The front side has no power supply and measures the power supply part;
3, the volume potentiometer is bad;
4. This fault occurs when the operational amplifier IC is bad.
If the pure power amplifier sound is distorted, the faulty part:
1. Power tube soft breakdown;
2. There is no voltage or low voltage between positive and negative voltages;
3. Resistance variable value, etc.
The sound normal level indicator does not work:
1. First measure whether the voltage is normal;
2. Then measure whether the signal is sent;
3. Measure whether the components are damaged.
The treble bass can't be adjusted:
1. Is the potentiometer normal?
2. Whether the voltage is normal;
3. Whether the RC component is normal;
4. Whether the line is connected or has poor contact;
5. Whether there are any solder joints or false solder joints in the solder joints.
The signal level indicator flashes normally, but there is no sound output: first check if the speaker unit is normal. If it is normal, check the speaker lead is normal, that is, check that the terminal is in good contact, normal, that is, open the case for visual inspection or listen to the ear or hear it. See if the output relay is closed. If the suction is normal, (if there is a universal meter), it is measured whether the front input and output of the relay are directly connected. If it is not connected, the contact in the relay is oxidized or fired to produce charcoal. The relay is normal.
The power light indicates normal no sound output, but the output relay hears the sound: first use the universal meter to measure whether the power supply of the power amplifier is normal, such as normal, that is, the signal line terminal of the signal input terminal is connected with the hand. The large current sound is the initial judgment that the power amplification part is basically normal, that is, whether the signal line of the light shaking signal is incapable or poorly contacted. If the contact is poor, the measurement with the universal meter is that the line is faulty and normal.
For example, when the power amplifier is output, there is no sound output: that is, it is normal to check the speaker unit. If the terminal is in poor contact, it will cause burnt. If the terminal is black, clean it to ensure normal contact, and tighten the screw.
The power-on protection light is on: First, use the universal meter to measure whether the speaker group has a short circuit, and whether the resistance is reduced (generally normal is not less than 30Ω). If the resistance value of the external circuit is normal, it is determined that the power amplifier is faulty, that is, it must be turned on.
The possibility that public broadcast sounds may occur when there are large and small phenomena is :
1. Poor contact of the signal line;
2. Poor contact of the potentiometer;
3. Signal coupling capacitor;
4. The feedback resistor is in poor contact.
In the case of measuring the power amplifier motherboard is normal, there is no sound:
The signal line is not connected or the coupling capacitor is open;
2. The front side has no power supply and measures the power supply part;
3, the volume potentiometer is bad;
4. This fault occurs when the operational amplifier IC is bad.
If the pure power amplifier sound is distorted, the faulty part:
1. Power tube soft breakdown;
2. There is no voltage or low voltage between positive and negative voltages;
3. Resistance variable value, etc.
The sound normal level indicator does not work:
1. First measure whether the voltage is normal;
2. Then measure whether the signal is sent;
3. Measure whether the components are damaged.
The treble bass can't be adjusted:
1. Is the potentiometer normal?
2. Whether the voltage is normal;
3. Whether the RC component is normal;
4. Whether the line is connected or has poor contact;
5. Whether there are any solder joints or false solder joints in the solder joints.
Basic processing method of public address power amplifier machine <br> No electricity: Check whether the power line to the fuse is open, whether the power line is broken or the fuse is in poor contact, the fuse is blown → check the rectifier bridge or electrolysis of the power amplifier rectifier power supply Whether the device is bad, such as rectifier diode or bridge stack, replace the good components and check other lines, such as power amplifier tubes.
The signal level indicator flashes normally, but there is no sound output: first check if the speaker unit is normal. If it is normal, check the speaker lead is normal, that is, check that the terminal is in good contact, normal, that is, open the case for visual inspection or listen to the ear or hear it. See if the output relay is closed. If the suction is normal, (if there is a universal meter), it is measured whether the front input and output of the relay are directly connected. If it is not connected, the contact in the relay is oxidized or fired to produce charcoal. The relay is normal.
The power light indicates normal no sound output, but the output relay hears the sound: first use the universal meter to measure whether the power supply of the power amplifier is normal, such as normal, that is, the signal line terminal of the signal input terminal is connected with the hand. The large current sound is the initial judgment that the power amplification part is basically normal, that is, whether the signal line of the light shaking signal is incapable or poorly contacted. If the contact is poor, the measurement with the universal meter is that the line is faulty and normal.
For example, when the power amplifier is output, there is no sound output: that is, it is normal to check the speaker unit. If the terminal is in poor contact, it will cause burnt. If the terminal is black, clean it to ensure normal contact, and tighten the screw.
The power-on protection light is on: First, use the universal meter to measure whether the speaker group has a short circuit, and whether the resistance is reduced (generally normal is not less than 30Ω). If the resistance value of the external circuit is normal, it is determined that the power amplifier is faulty, that is, it must be turned on.
The possibility that public broadcast sounds may occur when there are large and small phenomena is :
1. Poor contact of the signal line;
2. Poor contact of the potentiometer;
3. Signal coupling capacitor;
4. The feedback resistor is in poor contact.
In the case of measuring the power amplifier motherboard is normal, there is no sound:
The signal line is not connected or the coupling capacitor is open;
2. The front side has no power supply and measures the power supply part;
3, the volume potentiometer is bad;
4. This fault occurs when the operational amplifier IC is bad.
If the pure power amplifier sound is distorted, the faulty part:
1. Power tube soft breakdown;
2. There is no voltage or low voltage between positive and negative voltages;
3. Resistance variable value, etc.
The sound normal level indicator does not work:
1. First measure whether the voltage is normal;
2. Then measure whether the signal is sent;
3. Measure whether the components are damaged.
The treble bass can't be adjusted:
1. Is the potentiometer normal?
2. Whether the voltage is normal;
3. Whether the RC component is normal;
4. Whether the line is connected or has poor contact;
5. Whether there are any solder joints or false solder joints in the solder joints.
Basic processing method of public address power amplifier machine <br> No electricity: Check whether the power line to the fuse is open, whether the power line is broken or the fuse is in poor contact, the fuse is blown → check the rectifier bridge or electrolysis of the power amplifier rectifier power supply Whether the device is bad, such as rectifier diode or bridge stack, replace the good components and check other lines, such as power amplifier tubes.
The signal level indicator flashes normally, but there is no sound output: first check if the speaker unit is normal. If it is normal, check the speaker lead is normal, that is, check that the terminal is in good contact, normal, that is, open the case for visual inspection or listen to the ear or hear it. See if the output relay is closed. If the suction is normal, (if there is a universal meter), it is measured whether the front input and output of the relay are directly connected. If it is not connected, the contact in the relay is oxidized or fired to produce charcoal. The relay is normal.
The power light indicates normal no sound output, but the output relay hears the sound: first use the universal meter to measure whether the power supply of the power amplifier is normal, such as normal, that is, the signal line terminal of the signal input terminal is connected with the hand. The large current sound is the initial judgment that the power amplification part is basically normal, that is, whether the signal line of the light shaking signal is incapable or poorly contacted. If the contact is poor, the measurement with the universal meter is that the line is faulty and normal.
For example, when the power amplifier is output, there is no sound output: that is, it is normal to check the speaker unit. If the terminal is in poor contact, it will cause burnt. If the terminal is black, clean it to ensure normal contact, and tighten the screw.
The power-on protection light is on: First, use the universal meter to measure whether the speaker group has a short circuit, and whether the resistance is reduced (generally normal is not less than 30Ω). If the resistance value of the external circuit is normal, it is determined that the power amplifier is faulty, that is, it must be turned on.
The possibility that public broadcast sounds may occur when there are large and small phenomena is :
1. Poor contact of the signal line;
2. Poor contact of the potentiometer;
3. Signal coupling capacitor;
4. The feedback resistor is in poor contact.
In the case of measuring the power amplifier motherboard is normal, there is no sound:
The signal line is not connected or the coupling capacitor is open;
2. The front side has no power supply and measures the power supply part;
3, the volume potentiometer is bad;
4. This fault occurs when the operational amplifier IC is bad.
If the pure power amplifier sound is distorted, the faulty part:
1. Power tube soft breakdown;
2. There is no voltage or low voltage between positive and negative voltages;
3. Resistance variable value, etc.
The sound normal level indicator does not work:
1. First measure whether the voltage is normal;
2. Then measure whether the signal is sent;
3. Measure whether the components are damaged.
The treble bass can't be adjusted:
1. Is the potentiometer normal?
2. Whether the voltage is normal;
3. Whether the RC component is normal;
4. Whether the line is connected or has poor contact;
5. Whether there are any solder joints or false solder joints in the solder joints.
Adjustable Aluminum Laptop Stand,Laptop Stand Aluminium Adjustable Portable,Aluminum Laptop Stand Adjustable Height,etc.
Shenzhen Chengrong Technology Co.ltd is a high-quality enterprise specializing in metal stamping and CNC production for 12 years. The company mainly aims at the R&D, production and sales of Notebook Laptop Stands and Mobile Phone Stands. From the mold design and processing to machining and product surface oxidation, spraying treatment etc ,integration can fully meet the various processing needs of customers. Have a complete and scientific quality management system, strength and product quality are recognized and trusted by the industry, to meet changing economic and social needs.
Adjustable Aluminum Laptop Stand,Laptop Stand Aluminium Adjustable Portable,Aluminum Laptop Stand Adjustable Height
Shenzhen ChengRong Technology Co.,Ltd. , https://www.dglaptopstandsupplier.com